12 Oct

FAIRSEAL

GUN GRADE TWO PART POLYSULPHIDE SEALANT

Polysulphide sealant is design to seal joints subject to movement, where a tough flexible watertight seal is required. FAIRSEAL has Excellent weathering characteristics with resistance to rain, snow, heat & ultraviolet light.
FAIRSEAL is a two-part joint sealant based on liquid polysulphide polymer. It is based on liquid polysulphide polymer. When mixed and cured, the sealant exhibits excellent adhesion to most surfaces including concrete, glass aluminum & stainless steel. FAIRSEAL is suitable for sealing vertical joints only. FAIRSEAL has superior joint movement accommodation with strong adhesion to most building materials. It is chemically resistant to water, oils, solvents, etc.
FAIRSEAL may be applied to joints between 5 to 50 mm width / depth. Minimum joint depths are 5mm for metal, glass, and another non-porous surface. 10mm for all porous surfaces like brick and concrete. 20 mm for trafficked joints and those subject to hydrostatic pressure.

SALIENT FEATURES OF POLYSULPHIDE SEALANT,
• Quick curing with low shrinkage
• Accommodates continuous and pronounced cyclic movement
• High resistance to ageing influences, physical damage and climatic extremes
• Resistance to petrol, diesel, jet fuel and most other common solvents & also unaffected by mild acids and alkalis.

APPLICATION

SURFACE PREPARATION: Before the application of the sealant, all joint surfaces should be thoroughly cleaned and dried, and primed with FAIRSEAL PRIMER. Loose particles, dirt, dust, protective liquor, oil and grease should be remove by vigorous brush with a wire brush and by means of suitable cleaners e.g. KEROSENE. After the primer is applied, it has to be relatively dried before sealant is applied.

MIXING: FAIRSEAL sealant supplied as base and hardener (curing agent) in separate packing, ready for mixing. In order to mix both the compounds thoroughly, it is preferable to use a slow speed electric mixer with suitable blades or paddles with speed < 300 RPM. Make certain that mixing till a uniform color is obtained. Failure of sealant when it is not completely and thoroughly mixed.

FAIRSEAL is used for sealing expansion joints between structures in building construction like infill panels, metal finishes and in civil engineering structures like basements, buildings, walls, and brickwork joints, etc. FAIRSEAL is suitable for sealing vertical joints only. It is quick curing with low shrinkage. It is unaffected by mild acids, alkalis, & resistance to petrol, diesel, jet fuel, etc.

FINISHING: To obtain smooth surface, the sealant has to be tooled by drawing a flat tool, like a stainless steel spatula over its surface.
ESTIMATION OF QUANTITY
Formula: Weight in Kg = (1.6 X W X D X L)/1000
Where W & D are in mm and L is in metre,
Example
W (Width of joint) = 10 mm
D (Depth of joint) = 10 mm
L (Length of joint) = 12.5 mtr
Weight in Kg = (1.6 X 10 X 10 X 12.5) / 1000 =2kg of sealant
PACKING
FAIRSEAL is available in big packing of (4.6kg base + 0.4kg hardener) & small packing of (0.920kg base + 0.08kg hardener).
FAIRSEAL is highly inflammable & it must be stored away from heat & kept in dry condition.

By SEALANT 0 Comments Read more...
12 Oct

FAIRSEAL P

POURABLE GRADE TWO PART POLYSULPHIDE SEALANT

FAIRSEAL P is a two-part, pourable, self-leveling, polysulphide-based joint sealing compound consisting of the base compound containing a liquid polysulphide polymer and the second part being an accelerator containing a curing agent. After mixing, the compound cures to form a tough, rubber-like material with excellent flexibility and outstanding resistance to weathering water, salts, oils, mild alkalis, etc.
FAIRSEAL P is suitable for sealing horizontal joints due to its pouring consistency. It has excellent adhesion to most surfaces including concrete, wood, glass, aluminum, and stainless steel. For all porous surfaces like concrete wood, FAIRSEAL PRIMER is necessary.
FAIRSEAL P may be applied to joints between 5 to 50 mm width/depth. Minimum joint depths are 5mm for metal, glass, and other non-porous surfaces. 10mm for all porous surfaces like brickwork and concrete.
SALINET FEATURES OF POLYSULPHIDE SEALANT,

• Excellent weathering characteristics with resistance to rain, snow, heat & ultraviolet light
• It gets cured quickly with low shrinkage
• Accommodates continuous and pronounced cyclic movement
• High resistance to aging influences, physical damage, and climatic extremes
• Resistance to petrol, diesel, jet fuel, and most other common solvents & also unaffected by mild acids and alkalies
• Forms a tough elastic rubber-like seal
• Pourable grade sealant for horizontal joints Long service life
• Maintenance free

APPLICATION

SURFACE PREPARATION: Before the application of the sealant, all joint surfaces should be thoroughly cleaned and dried, and primed with FAIRSEAL PRIMER. Loose particles, dirt, dust, protective liquor, oil, and grease should be removed by vigorous brushing with a wire brush and utilizing suitable cleaners e.g. KEROSENE. After the primer is applied, it has to be relatively dried before a sealant is applied.
MIXING: FAIRSEAL P sealant is supply as base and hardener (curing agent) in separate packing, ready for mixing. To mix both the compounds thoroughly, it is preferable to use a slow-speed electric mixer with suitable blades or paddles with a speed of < 300 RPM. Ensure thorough mixing till a uniform color is obtained. Failure of sealant will often occur if it is not completely and thoroughly mixed. After mixing FAIRSEAL P may be poured directly into horizontal joints or loaded into the gun for application to horizontal joints less than 15mm wide.

FAIRSEAL P is suitable for sealing horizontal structure expansion joints like building superstructures, subways, basements, floors, PQC roads, airport runways, and reservoirs. It is a pourable grade sealant for horizontal joints. It is a tough elastic rubber-like seal. It is unaffected by mild acids, alkalies, & resistance to petrol, diesel, jet fuel, etc. It gets cured quickly with low shrinkage.

FINISHING: To obtain smooth surface, the sealant has to be tooled by drawing a flat tool, like a stainless steel spatula, over its surface.
ESTIMATION OF QUANTITY
Formula: Weight in Kg = (1.6 X W X D X L)/1000
Where W & D are in mm and L is in metre,
Example
W (Width of joint) = 10 mm
D (Depth of joint) = 10 mm
L (Length of joint) = 12.5 mtr
Weight in Kg
= (1.6 X 10 X 10 X 12.5) / 1000 = 2kg of sealant
PACKING
FAIRSEAL is available in big packing of (4.6kg base + 0.4kg hardener) & small packing of (0.920kg base + 0.08kg hardener).
FAIRSEAL is highly inflammable & it must be stored away from heat & kept in dry condition.

By SEALANT 0 Comments Read more...
12 Oct

WATERGUARD COOL COOL

SINGLE COMPONENT, ACRYLIC BASED FLEXIBLE, INSULATING CUM WATERPROOFING COATING

WATERGUARD COOL COOL is a single component, flexible, ultra violet rays, weather-resistant, and acrylic-based waterproofing coating. WATERGUARD COOL COOL provides extremely long-lasting protective coating that creates a thermal barrier that stands against severe temperatures and changes and provides long-lasting protection against wind and rain. It protects concrete against attack from atmospheric carbon dioxide, airborne chlorides, acid, rain, weathering, etc. WATERGUARD COOL COOL is ready to use, ensuring waterproofing. It also provides extremely tough decorative waterproof coating, which allows breathing on the surface.

SALIENT FEATURES
• Can be applied on vertical & horizontal surfaces
• Colours are stable
• Gives insulation properties
• Flexible, Cost effective and easy to apply
• Excellent water tightness
• Durable – high UV resistance
• Non-conductive property saves air conditioning energy cost
• Excellent adhesion to most building substrates

APPLICATION PROCEDURE
All dust, loose and friable materials, and glaze or varnish on tiles must be completely removed by mechanical means.The prepared surface should be thoroughly wetted with water for absorption, and excess water should be removed. Waterguard Cool Cool should be applied in 2/3 uniform coats after mixing the pre-weighted quantities as per technical specifications. The second coat can be applied perpendicular to the first coat after the first coat is dry. There can be overlapping of layers. It is recommended to wait for 6–8 hours before applying the second coat. Sprinkle fine aggregates immediately after the second coat of application.

WATERGUARD COOL COOL is designed for use as a thermal insulation coating and waterproofing on roof slabs and walls (new or old) of buildings.
It can also be used on the interior walls, exterior walls, and the roof of freezer rooms and cold storage facilities.

PACKING & COVERAGE
WATERGUARD COOL COOL is supplied in 1, 5, 20 kgs.
It has coverage of 4-5 m²/kg/two coats (200 microns WFT).
Coverage of WATERGUARD COOL COOL depends on the surface.

By Waterproofing Chemicals 0 Comments Read more...
12 Oct

WATERGUARD A

TWO COMPONENT, ACRYLIC CEMENTITIOUS WATERPROOFING COATING

Many people are facing leakage and damp problems on their home terraces during the monsoon season. To come out of this problem we request you to use our WATERGUARD A.

WATERGUARD A is a prepacked two-component acrylic modified cementitious waterproofing coating. One part is liquid in white color and another is powder in grey color. After mixing both components at the site it produces a mix that is easy to use. It should be applied in 2-3 uniform coats
SALIENT FEATURES
• Prepacked easy to use water proofing coating
• Non-toxic & environmental friendly
• Excellent adhesion
• Minimum surface preparation needed
• Allows surface to breath
• Approved for potable water contact
• Economical system
APPLICATION PROCEDURE
1. Surface preparation
• Make sure all the leakage and water jet points are sealed.
• Clean the surface with wire brush and remove all loose particles.
• If any cracks are visible, repair them.
2. Mixing
• Pour the liquid polymer in the container or electrical mixer.
• Slowly add powder in it and mix continuously until the required consistency is obtained.
3. Application
• Sprinkle water on the prepared surface and allow absorption. Remove excess water from the surface.
• Stir the WATERGUARD A before applying.
• Apply uniform coat of WATERGUARD A with brush, and leave it for drying.
• Apply 2nd or subsequent coat after previous coat is dried.
• Cure the surface for 3-5 days.

WATERGUARD A is used to protect the structure against the ingress of moisture. It is used in water retaining structures like water tank, swimming pools, retaining wall, bridge walls, reservoirs, dams, dock gates etc. it is also used in and around house component like roof, terrace and balconies, basement, Lift shaft etc.

By Waterproofing Chemicals 0 Comments Read more...
12 Oct

FAIRMATE WATERPLUG

A FAST SETTING PLUGGING COMPOUND FOR STOPPAGE OF RUNNING WATER

FAIRMATE WATERPLUG is a blend of cement well-graded sands and special additives in dry powder form. It requires only the addition of clean water to produce a ready-to-use, ultra-rapid setting and plugging mortar. FAIRMATE WATERPLUG is based on a mixture of cement, aggregates, and special fillers which minimises the risk of thermal cracking.

SALIENT FEATURES
• Stops running water instantly
• Sets under water
• Non shrink, non-metallic
• High structural strength
• Easy to use- simply add water
• Low exothermal minimises thermal cracking.

APPLICATION PROCEDURE

SURFACE TREATMENT
• Chisel out masonry around the hole or crack to a depth and width not less than 25 mm. Ensure that the hole is wider within the wall than at the surface. (Inverted ‘V’ Groove).
• If the water pressure is high at the area to be patched, make weep holes at the base of the wall to relieve the pressure.
• All loose material & debris should be removed.

METHOD OF USAGE

• FAIRMATE WATERPLUG should be mixed with a trowel in small quantities 1:4 by volume or 1:5 by weight (water to FAIRMATE WATERPLUG).
• Hold the mixed FAIRMATE WATERPLUG in the gloved hand until heat generation is felt and force the material in to the crack or void and hold tightly with palm of the hand for 3 minutes until FAIRMATE WATERPLUG sets.

FAIRMATE WATERPLUG is used as plugging mortar for fixing nozzles or grouting operations. It is also uses for arresting instant water seepages through dams, water tanks, basements, sunken pits, floor junctions.

PACKING & COVERAGE
FAIRMATE WATERPLUG is supplied in 1 kg, 5 Kg, 25 kg Bag.

By Waterproofing Chemicals 0 Comments Read more...
12 Oct

WATERGUARD LIQUID MEMBRANE

POLYMER MODIFIED BITUMEN BASED FIBER REINFORCED FLEXIBLE, LIQUID APPLIED WATERPROOFING MEMBRANE

WATERGUARD LIQUID MEMBRANE is polymer-modified water based on bitumen, liquid applied, fiber reinforced flexible, damp-proof, and vapor-proof liquid membrane. WATERGUARD LIQUID MEMBRANE is highly resistant to aggressive soils and soluble salts providing an effective continuous barrier and protection against water Bourne damage. If a water flood test is to be run, the membrane should cure for a minimum of 7 days. Whilst WATERGUARD LIQUID MEMBRANE is resistant to frost, adhesion will be impaired if applied to frosted substrates.

SALIENT FEATURES
• free from solvents
• Very low permeability
• High elasticity, ensuring a permanently flexible barrier over a wide range of temperatures
• Thermally stable – irreversible chemical cure eliminates melting and flow at high temperature
• Can be applied to a range of substrates
• Outstanding resistance to oxidation and brittlement
• Fibers improve tensile strength and abrasion resistance

APPLICATION PROCEDURE
Surface preparation: All substrates must be sound, clean, dry, smooth and free from protrusions, voids, honey-combs and high spots. Presence of curing agents, paint and oil will impair adhesion.
Moss and lichen must be removed and area treated with proprietary fungicidal wash to kill spores and inhibit further growth. Following treatment wash area thoroughly with clean water and allow drying. Fillets must be provided at corners or sharp angles using 4:1 sand and cement mortar modified with a good quality bonding agent – FAIRCRETE SB (L).

Priming: Priming is not normally required on good quality, well prepared substrates.

Cracks: All shrinkage and non-structural cracks must be treated with not less than 1.5mm coating of WATERGUARD LIQUID MEMBRANE extending 75mm either side of the crack. Allow to cure overnight prior to general application.

Application: WATERGUARD LIQUID MEMBRANE should be applied by brush to obtain a continuous unbroken film. Two coats are required with the second coat applied at right angles after the first coat has dried. WATERGUARD LIQUID MEMBRANE must be protected from mechanical damage during subsequent construction or backfilling works. Any damage may be repaired by spot application. Application should be avoided if substrate temperatures are below 5ºC or rain is imminent.

Curing: Allow each coat to dry a minimum of 24 hours before re-coating. full cure may take after 7 days of application or more depending on temperature conditions. Cold temperatures will slow cure time, higher temperature may speed up cure time.

WATERGUARD LIQUID MEMBRANE is particularly suitable for a wide range of applications including wet areas, foundations, basements, terraces, retaining walls, bridge abutments, planters, inverted roofs and remedial repairs to felt, asphalt, concrete, fibreous cement or other roof structures when protected from exposure to direct sunlight.

PACKING & COVERAGE
WATERGUARD LIQUID MEMBRANE is supplied in 20 kg pails. It has a coverage of 1.5 – 2 m² per kg at 1mm WFT.
Coverage rate will vary with substrate condition and profile.

By Waterproofing Chemicals 0 Comments Read more...
18 Aug

SETRELEASE ECO

A mould release agent is a chemical substance that creates a moulding surface barrier so that products don’t get stuck to a mould. We are well aware of the need to use mould release agent for concrete and formwork, as it is very crucial to prevent the concrete from sticking to the surface of the mould.
When a proper mould release agent is not used it has been observed that it becomes difficult to remove the mould and even the finish of the concrete is not aesthetically pleasing. To achieve easy removal of mould and a good smooth finish of the concrete surface it is advisable to use an excellent performing mould release agent.
Our SETRELEASE ECO is a wonderful product in itself, it is an eco friendly, biodegradable oil based mould release agent. It has no impact on the mould besides allowing it to detach from the concrete leaving a smooth finish.
It is a specially formulated blend of bio degradable oil based mould release agent, which is superior then conventional mould oil. The chemicals react with the alkali in the concrete to form a thin water repellent skin on the surface of the mould, thereby enabling easy stripping from concrete and protects steel and wooden formwork. SETRELEASE ECO is supplied as ready to use liquid.
Due to the excellent release properties, little or no deposit of cement paste remains on the shutter surface. Minimum cleaning & a further coat of SETRELEASE ECO renders shuttering ready for re-use.
SETRELEASE ECO provides quick, clean and easy stripping of moulds and formwork. It ensures high quality, fair-faced and stain-free concrete surface. Protects aluminium windows and door frames from plaster and mortar splashes.

SALIENT FEATURES:
• ECO friendly
• Ensures good fair-faced concrete
• Can be used on all type of formwork
• Non-staining
• Minimises cleaning of shutters before reuse
• Can be used with steam curing
• Reduces the incidence of air pocket and tendency of surface spalli ng of corners
• Economical

*Applicable on all types of formwork*

APPLICATION:
SETRELEASE ECO can be applied by brush, sponge or conventional mould oil-sprayer. If an oil sprayer is used, care should be taken to choose correct size of
sprayer. Apply one thin and even coat of SETRELEASE ECO over the entire surface. Even a thin coat is enough to achieve effective coverage.
Excess application is uneconomical and may lead to surface dusting. Wire or brush off any excess particles on the surface and apply one coat of SETRELEASE ECO as before. To remove SETRELEASE ECO completely, for recoating mould or shutter surface, use strong industrial detergent together with stiff brushing & then thoroughly rinse with clean water. It is recommended that after application of SETRELEASE ECO concrete pouring to be done within 24 hrs or same day.

COVERAGE:
A coverage between 40 to 60 m²/litre is possible depending upon the porosity and texture of mould surface.

By SURFACE TREATMENT 0 Comments Read more...
23 Jun

FAIRCURE WX WHITE

FAIRCURE WX WHITE is a wax based concrete curing compound. It is white coloured curing compound. When it is applied on the concrete surface, it forms a continuous layer of wax over it. The wax layer remains on the surface of concrete, but do not penetrate into surface. It only breaks by natural weathering or anyone remove it by scratching. FAIRCURE WX WHITE is useful where curing cannot be done by water ponding like on vertical or inclined surface.

FAIRCURE WX WHITE can be used on fresh concrete surface and newly exposed concrete surfaces after removal of formwork. It can be used for pavement, runway, bridge deck, towers, chimneys, canal lining, columns and beams.

Benefits of wax based concrete curing compound:

There are various benefits of wax based concrete curing compounds. Some of them are given below:

• By obtaining superior strength, it helps in completing the hydration of the cement.
• It also provides a water repellent film.
• The biggest advantage of this compound is that it can be used with all types of cement.
• As it reduces the breaking of the edges while lifting the elements, therefore, it helps in saving the cost of production.

SALIENT FEATURES of FAIRCURE WX WHITE
• Only single coat required for whole of the curing period
• Reduce water usage
• Ensures perfect curing
• Ensures hard wearing surface
• Easy to use and apply
• Reduce labour cost
• Time saver
• Easy to identify treated surface

APPLICATION PROCEDURE
• Stir well the liquid curing compound before applying.
• Fill the stirred liquid in the high volume low pressure spray.
• Start applying uniform coat of FAIRCURE WX WHITE and keep nozzle of spray 40-50cm from concrete surface. Move the nozzle back and forth to ensure complete and even coverage. The pump pressure should be maintained at a level to produce a fine spray.
• For newly placed concrete, apply FAIRCURE WX WHITE as soon as visible surface moisture is invisible, e.g. typically 1/2 to 2 hours after placing shuttered and precast concrete.
• For demoulded concrete surface, apply FAIRCURE WX WHITE immediately after removing mould/ formwork.

PACKING AND COVERAGE
FAIRCURE WX WHITE is supplied in 1, 5, 10, 50, 100, 200 Ltr. carboys. FAIRCURE WX WHITE has coverage of 5 to 6 m² per Ltr.

By SURFACE TREATMENT 0 Comments Read more...
15 Mar

CEMSCREED HM(F)

With time the hardened concrete loses its ability to hold the binding concrete materials together due to weathering or atmospheric condition. Concrete repair products are used to repair building cracks, surface scaling, damaged or chipped out concrete surface etc.

Benefits of Concrete:
1) Prevents Longevity
2) Prevents further damage to concrete
3) Reduces the risk of injury
4) Stays Functional

Every time your concrete structure has cracks or it is has started scaling or chipping off there is a good chance of moisture entering into that part of the concrete structure which can cause more damage to the structure and even cause corrosion of the structural reinforcement. The moisture seepage can cause the cracks to even widen due to the freeze and thaw reaction cycle.
It better repair material can increase the lifeline of the structure by giving it back its durability which in longer run saves time and money and frequent repair work is not allowed.

CEMSCREED HM(F):
It is a ready to use blend of dry powder which only requires water addition to it making it a free flowing, non shrink repair mortar. It is a micro concrete repair mortar infused with fibres which help to compensate the shrinkage of concrete. It gives high early strength and long term durability due to less water requirement. It is suitable for all types of structural repair work of load bearing locations.

CEMSCREED HM(F) is used to repair columns where a major material loss is observed, for soffit repair work, for repair in areas where use of hand applied mortar is not practically possible or even the reinforcement is very heavily congested. It is used to do beams and columns jacketing work.

For larger repair work 12mm clean, well graded, saturated, surface dry aggregate shall be added to CEMSCREED HM(F).

Coming to the application of the product it is required to make sure the surface preparation is done very well, for that cut back the defective concrete till a sound base is reached. If there is a smooth surface then roughen the surface to make sure the new material can be adhered to the old surface properly. If there is any exposed corroded reinforcement, then check the whole circumference of the bar and clean all the rust and corrosion from it. After that you can apply SAFECORE R product on the exposed reinforcement bars to stop it from getting corroded further due to any reasons. Make sure that the surface is wetted properly and any access water present is removed. Apply FAIRBOND EP as a bonding primer on the prepared surface and then pour/ place CEMSCREED HM(F) using pump. After the placing is done curing shall start after 2 hours for as long as concrete curing is required.

SARDAR SAROVAR PROJECTS

Before Application | During Application | After Application

Salient Features:
 Compensates for shrinkage in the plastic stage
 Can be pumped or poured into restricted locations
 Highly fluid to allow placement without vibration
 Pre-packed factory controlled to overcome site- batched variations
 Rapid strength gain to facilitate early reinforcement
 High Ultimate strength and low permeability of cured repair
 Does not contain any corrosive chemicals
 Ensures high tensile strength
 Specially reinforced with polypropylene fibre
 Cost Effective
 Enhanced durability

By Concrete Repair 1 Comment Read more...
22 Feb

FAIRMATE STAMP CONCRETE

Stamp concrete is a decorative and intelligent approach for exterior floor surfaces. This approach to exterior floor surfaces is very cost effective and there are lot of design options available such as surface resembling to paver, flagstone, slate, worn rock, bricks, stones, tiles or wood with various colour options. Further coating of stamp concrete can give a glossy finish for better aesthetics. The process includes preparation of sub-grade, placing of forms, providing reinforcement for stability, placing the concrete, screed and finishing the concrete, applying colour and lastly stamping the concrete using desired moulds.
Stamped concrete can make a dramatic impression, and there are many reasons why home owners are choosing this authentic material to enhance their landscapes and buildings. Along with the known durability and long lasting feature of regular concrete, stamping adds a decorative touch making it a desirable and economical product for all.

What are the benefits of Stamp Concrete?

 It is durable and long lasting, which can last for decades without the requirement of renovation.
 It is available in many colours and patterns.
 Can be installed twice as fast as natural stones and pavers.
 Can be customised with lots of design possibilities
 Better resistance to traffic and moisture
 Increased durability

Procedure of creating decorative outdoor flooring with stamp

Concrete:

 Surface preparation: The sub-grade is important for concrete and therefore it must be well compacted due to settlement or cracks due to settlement.
 Formwork placement: formwork should be clean and should be able to withstand the concrete placement.
 Placement of reinforcement: Nominal reinforcement is usually placed for structural function to provide structural integrity to avoid cracks and increase impact resistance.
 Apply a layer of screed for levelling and giving a proper finish to the surface.
 Then apply FAIRMATE STAMPCRETE HARDENER through broadcasting on the screed when it has reached the desired surface plasticity. After the first layer of broadcasting let it absorb water from the concrete and float it using a bull floating.
 Apply second layer of coloured hardener for better coverage.
 Next apply FAIRMATE STAMPCRETE RELEASE AGENT to make it easily for removing the stamp without sticking to the concrete surface.
 Before stamping check whether the concrete has attended the right amount of Plasticity. Stamping too early and too late can spoil the whole work and desired results will not be obtained.
 The stamping: Before actual stamping, the stamp layout is diagrammed and enough workers are deployed as the window of time for stamping is generally short, especially in warm weather. Typically, the edges are pre-textured first so that when larger stamps are used later, they may not overlap the forms and get fully depressed into the concrete. The concrete is then stamped in the same sequence it was placed. Stamping alignment is checked regularly verifying the pattern to ensure desired outcome.
 Once the slab has cured sufficiently, you should apply a finish coat of sealer. Most manufacturers recommend applying the sealer several weeks later, after a light surface cleaning. Be careful not to apply the sealer too heavily, which could trap moisture in the slab. One of the most effective techniques for applying sealer is to combine both spraying and rolling, especially when the stamped pattern has deep grout lines. Going back over the surface with a roller where necessary helps to distribute the sealer uniformly.

Some amazing results of stamp concrete by FAIRMATE:

By Architectural Finish 0 Comments Read more...